Vinyl fencing can also be built using panels which are usually 8-foot-wide and 6-foot-high. White vinyl fencing costs$120 per panel, wood-look costs$235, and black vinyl costs$370 per panel. If you have hard clay soil or soil that’s riddled with rocks, you may not be able to drive down the fence posts to a consistent height later . If that’s the case, dig the holes a few inches deeper, then add sand on the bottom and set the posts. Now you’ll be able to drive down the posts as needed. Start by driving stakes beyond the end or corner positions, and then string a taut line between them even with the outside of the post locations.
Drop a post into each and adjust the depth to position the bottom rail 4 in. Not recommended, as the wooden posts can rot and leave the vinyl posts without support. If you need an entry point along the fence, it’s also important to purchase a vinyl gate kit that fits with the fencing you choose. Gates often come with hinges, or you can buy a fence gate kit which converts a fence panel to a gate and includes all necessary gate hardware and hinges for$80 to $100.
If you have a steep sloping property to fence, take advice from your supplier regarding the type of 카지노사이트 that best suits the purpose. While fencing slopes, we shall keep the rails parallel to the ground while the pickets are vertically added, not at an angle. If you have a big crew and expect to get a big fence installed in a day or two, it’s worth renting a cement mixer and a power auger to save on time and labor. Otherwise, just hand-mix the concrete in a wheelbarrow and dig the holes by hand.
After installing a post and before the concrete has set, check that it is plumb by placing a level on two adjacent sides or by using a post level. To ensure the posts are even in height, run a tight string line between corner posts and end posts. Before diving into a project unprepared, consider the most common pitfalls. Overlooked building regulations, poorly set posts, and insufficient prep work can create problems that quickly eat into those savings and shorten the life of a fence. If you want your vinyl fence project to stand as a testament to your DIY abilities for a long time, you’ll need to make sure you follow some important dos and don’ts.
A cheap traffic cone works great as a funnel; just cut the tip shorter for a larger hole. Start by picking up a fence permit application from the local building inspections department, along with local fence regulations. They will include setback requirements from your property lines to the fence and maximum heights. These details will likely vary for front and backyard fences and can even be different for houses on corners or busy streets. If you properly space and set your fence posts, assembling the fence panels is much like snapping together LEGO blocks. Rails snap into the post slots and are held in place with locking tabs.
Measure your property and calculate the number of posts and panels. Or, if it helps, involve your supplier during this planning phase to make sure there is no room for errors. You don’t want to hit any utility line underneath while digging for the posts, do you?
And, never make the mistake of digging shallow holes as the strength of your fence comes from the posts fixed on deep cement-filled holes. The depth of the hole depends upon your vinyl post lengths. Generally, it is advised to dig holes of depths that are 1/3 of vinyl posts’ lengths. Make sure that the lower notch of the post is just a few inches above the ground. Onto the most daunting step of the project – digging the holes. Manually, doing this can take a lot of your time and effort.
Moreover, fix the post as you go on and not all at once, as a small measurement problem might amplify to be a big issue if you fix all the posts in haste early on. Plenty of dirt and stones will be excavated out while digging for posts. Many choose to reuse the dirt and discard the stones. If you plan the same, make a plan to where to dump the stones. As the name suggests, privacy fences are for you if you’re in search of fencing that provides you with utmost privacy.
The only accurate way to determine if each post is straight in the ground and even in height with the other posts is to use a quality level. Your fence is only as strong as the posts holding it up, so set each post securely in the ground—especially if you are in an area with high winds or soft soil. Posts with shallow holes are more likely to eventually lean under the weight of the fence or even blow over altogether in extreme weather. Once you’ve located the utility lines and established your property line, mark the perimeter of your fence with a can of brightly colored spray paint. Finally, clear away any rocks, plants, or debris that might be in the way. Since the posts and pickets are hollow, they must be capped at the top.
